- Location
- Bayside, NY
Hydro Logic Stealth 100 ppm readings
- Thread starter PHiLiPSKim
- Start date
Has this unit ever read 0 ppm? Ideally that is the number you are looking for.
Do you have a hand held TDS meter to check the number with? ..a local reefer nearby who might have one?
After doing some reading it seems this unit is more designed for hydroponics than reef tanks where a zero ppm is the goal. The fact that it only uses 2 chambers, rather than the 4 or 5 that most reef RO/DI systems have, would be a concern.
Did you purchase this unit new? If not, the membrane may need replacing (no idea how long they last in a unit of this type), but i would venture a guess that with only 2 chambers prior to the membrane, that the membrane would burn out faster due to the quality of the water (still 'dirty') that it is trying to process.
I would also be concerned that after changing the membrane you still might not have zero TDS water as it doesn't promise that in its advertising
You might want to consider adding a DI Resin cartridge to your unit so you can get the TDS reading down to zero. A reading of 36 or 38 is WAY too high.
Do you have a hand held TDS meter to check the number with? ..a local reefer nearby who might have one?
After doing some reading it seems this unit is more designed for hydroponics than reef tanks where a zero ppm is the goal. The fact that it only uses 2 chambers, rather than the 4 or 5 that most reef RO/DI systems have, would be a concern.
Did you purchase this unit new? If not, the membrane may need replacing (no idea how long they last in a unit of this type), but i would venture a guess that with only 2 chambers prior to the membrane, that the membrane would burn out faster due to the quality of the water (still 'dirty') that it is trying to process.
I would also be concerned that after changing the membrane you still might not have zero TDS water as it doesn't promise that in its advertising
You might want to consider adding a DI Resin cartridge to your unit so you can get the TDS reading down to zero. A reading of 36 or 38 is WAY too high.
- Location
- Brooklyn, NY
36-38 ppm is the typical ( maybe even a little high) TDS for unfiltered NYC tap water!
- Location
- Bayside, NY
I got the unit in feb. and yrs I think I seen it at like 05-06. But it's at 36 so I changed the two filters. And when I pressed the in flow indicator it's reading 35. Lol like the filters changed only did .01 to the rpm. I wonder if I have to change more
Are you sure you are looking the right thing?
Are you reading the TDS of the water going in or out? (just want to be sure we are all on the same page
)
Last edited:
- Location
- Bergen Cnty. New Jersey
Did you change the membrane, thats the one that is going to lower the TDS. Do you have a flush kit on the unit?
- Location
- Ridgewood, NY
You're correct, I get 36 ppm steady at home.
- Location
- Bayside, NY
That's gross lol I thought NYC water was suppose to be good lol. But yea my ppm readings are still at 37. I'm sure it should be lower like 7 or so no?
- Location
- north jersey
37 ppm is actually pretty darn good for drinking water. many "bottled" drinking water has a higher reading than that (60-80 ppm).
my jersey well water is 240-260 ppm at the faucet, i'm getting about 4-5 ppm after the membrane and 0 after the di.
if you're using the 98% rejection rate membrane, you should get only 2% reading of the pre-membrane reading. in my case 2% of 240-260 ~5.....my membrane is working like it should.
- Location
- Rocky Point, NY
If I remember correctly, anything under 400ppm is considered safe for drinking water. I like the flush valve idea. It can extend the life of the membrane. I made one myself.
Sponsor Reefs
We're a FREE website, and we exist because of hobbyists like YOU who help us run this community.
Click here to sponsor $10:
